--- title: "U-Line error code Evap T Short" description: "U-Line error code Evap T Short: The evaporator thermistor circuit is shorted. Which machines can actually raise it, where the number lives on this make, and what to do next." url: "https://ulinemiami.support/error-codes/error-code-evap-t-short/" date_modified: "2026-08-30" Appliance type: "Beverage centers, Undercounter refrigerators, Wine coolers" --- # U-Line error code Evap T Short ### What Evap T Short means, in the maker’s own words The evaporator thermistor circuit is shorted. The same sensor as Evap T Open and the opposite failure: the cable is pinched or crushed rather than broken or disconnected. Unlike the E numbers on the rest of this make, this one is shown to you: the 3000 Series monitors its inputs continuously and puts the notification on the user interface rather than only into a service log. ### Quoted rather than interpreted > Evap T Short — Inspect thermistor cable for pinch points or damage. Replace if necessary. From the service diagnosis guide, 3000 Series User Guide, in a User Guide & Service Manual downloaded from U-Line’s own site. Nothing on this page is decoded beyond what that sentence says. ### Where this notification actually lives On your display, which on this make is the exception rather than the rule. The 3000 Series does not use the E numbers at all: it watches its inputs continuously and writes the notification on the user interface in plain words, so there is no hidden log to open and no key to hold. Every other U-Line in this catalog does the opposite — it logs the number in memory and shows you nothing but the door. If you are reading a phrase rather than a number, this is the series you own. ### What to do about it - Inspect the thermistor cable for pinch points or damage and replace it if necessary. - Inspect the wire harness from the main control board for pinch points or damage and repair it. - Expect the same frost story as the open circuit: defrost timing is what this sensor is for, so ice on the coil arrives before any change you can feel in the cabinet. - If the unit has recently been serviced or reinstalled, say so when you book. A harness pinched on reassembly is the most common history for a short on a cabinet that worked the day before. ### Where this goes next The job this usually becomes is [diagnostic visit](/services/diagnostic-visit/), and every one of those pages carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 851-2207](tel:+13058512207) and describe what the display is doing before booking anything. **u line evap t short error** names a notification the 3000 Series puts on the display itself, which is what makes it different from every other number this maker logs. 3000 Series only — this series does not use the E numbers What this one means What Evap T Short means, in the maker’s own words The evaporator thermistor circuit is shorted. The same sensor as Evap T Open and the opposite failure: the cable is pinched or crushed rather than broken or disconnected. Unlike the E numbers on the rest of this make, this one is shown to you: the 3000 Series monitors its inputs continuously and puts the notification on the user interface rather than only into a service log. Quoted rather than interpreted Evap T Short — Inspect thermistor cable for pinch points or damage. Replace if necessary. From the service diagnosis guide, 3000 Series User Guide, in a User Guide & Service Manual downloaded from U-Line’s own site. Nothing on this page is decoded beyond what that sentence says. Where this notification actually lives On your display, which on this make is the exception rather than the rule. The 3000 Series does not use the E numbers at all: it watches its inputs continuously and writes the notification on the user interface in plain words, so there is no hidden log to open and no key to hold. Every other U-Line in this catalog does the opposite — it logs the number in memory and shows you nothing but the door. If you are reading a phrase rather than a number, this is the series you own. What to do about it Inspect the thermistor cable for pinch points or damage and replace it if necessary. Inspect the wire harness from the main control board for pinch points or damage and repair it. Expect the same frost story as the open circuit: defrost timing is what this sensor is for, so ice on the coil arrives before any change you can feel in the cabinet. If the unit has recently been serviced or reinstalled, say so when you book. A harness pinched on reassembly is the most common history for a short on a cabinet that worked the day before. Where this goes next The job this usually becomes is diagnostic visit, and every one of those pages carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 851-2207](tel:+13058512207) and describe what the display is doing before booking anything. u line evap t short error names a notification the 3000 Series puts on the display itself, which is what makes it different from every other number this maker logs. --- **[Read full article: U-Line error code Evap T Short](https://ulinemiami.support/error-codes/error-code-evap-t-short/)**